Project Guides
PRACTICAL HELP FROM YOUR NEIGHBORHOOD HARDWARE STORE
Project Guides
Planning a fresh coat of paint, a healthier lawn, or a weekend repair? Start with our shopping checklists and material estimates. Country Paint & Hardware in North Branford is here to help you choose supplies and work through your project questions.
Click a guide title to open it.
These guides help with planning and shopping. Examples are estimates, not product-specific instructions. Always check the exact product label for coverage, compatibility, application, and safety information. Contact us to confirm product availability.
Lawn & Garden
Plan your quantities before you start planting, feeding, or refreshing your yard.
1. Grass Seed: How Much Do You Need?
Before you shop
Measure your lawn and note its sunlight. Are you starting a new lawn, overseeding existing grass, or repairing bare spots?
Shopping checklist
- Grass seed suited to your site
- Rake or soil loosening tool
- Spreader and hose or sprinkler
- Starter fertilizer if supported by your soil test and product instructions
- Seed covering if recommended on the label
Estimate your quantity
Pounds of seed = lawn area in square feet ÷ 1,000 × the label's seeding rate.
Example: A 2,500-square-foot area at 5 pounds per 1,000 square feet needs 12.5 pounds of seed.
New lawn and overseeding rates differ. Follow your specific seed label, prepare good seed-to-soil contact, and maintain the recommended moisture.
Explore Lawn & Garden →2. Lawn Fertilizer: Bag Coverage
Before you shop
Know your lawn's square footage, grass type, and spreader model. Bring any soil-test recommendations.
Shopping checklist
- Fertilizer appropriate to your lawn and season
- Compatible spreader
- Gloves and a broom for cleanup
Estimate your quantity
Bags needed = lawn area ÷ coverage per bag. Round up to whole bags.
Example: A 7,500-square-foot lawn with a product covering 5,000 square feet per bag requires two bags. Apply only the amount required for your lawn.
Use settings for your exact fertilizer and spreader. Follow application limits, avoid overlapping passes, and sweep granules off pavement.
Explore Lawn Care Supplies →3. Mulch: Bags or Cubic Yards
Before you shop
Measure each bed's length and width. Decide how much additional depth you need, accounting for existing mulch.
Shopping checklist
- Mulch in your preferred type and color
- Rake, wheelbarrow, and edging as needed
Estimate your quantity
Cubic yards = area in square feet × depth in inches ÷ 324.
For 2-cubic-foot bags: area × depth in inches ÷ 24.
For 3-cubic-foot bags: area × depth in inches ÷ 36.
Example: A 300-square-foot bed at 3 inches deep needs about 2.78 cubic yards, 38 two-cubic-foot bags, or 25 three-cubic-foot bags.
Keep mulch away from trunks and foundations. Allow for irregular bed shapes and confirm each bag's volume.
Ask About Bulk Mulch & Delivery →4. Topsoil & Compost: Volume Planning
Before you shop
Measure the area and intended depth. Tell us whether you are top-dressing, filling a bed, or improving existing soil.
Shopping checklist
- Topsoil or compost appropriate to the project
- Rake, shovel, and wheelbarrow
- Soil test if needed
Estimate your quantity
Cubic feet = area in square feet × depth in inches ÷ 12.
Cubic yards = area in square feet × depth in inches ÷ 324.
Example: A 200-square-foot area at 2 inches deep needs about 33.3 cubic feet, or 1.23 cubic yards.
Soil settles. Compost is a soil amendment and is not automatically a substitute for topsoil. Avoid burying existing turf under a thick layer.
Explore Garden Supplies →5. Lawn Repair: Bare Spots
Before you shop
Measure the bare patches and consider the cause: shade, pet damage, traffic, compaction, or drainage.
Shopping checklist
- Seed suited to the location
- Rake or hand cultivator
- Topsoil or compost if needed
- Seed covering as directed by the product
- Watering can or sprinkler
Estimate your quantity
Seed pounds = total patch area ÷ 1,000 × the label's new-seeding rate.
Example: A 150-square-foot patch at 6 pounds per 1,000 square feet needs 0.9 pound of seed.
Address the cause of the damage first. Follow preparation and watering instructions, and check herbicide waiting intervals before seeding. Seed-covering products have their own coverage rates.
Explore Lawn Repair Supplies →Hardware & Masonry
Build a shopping list and estimate materials for installations and repairs.
6. Concrete: Choosing Mixes & Estimating Bags
Before you shop
Bring slab dimensions or hole diameter and depth. Note any post dimensions and whether the project is structural or load-bearing.
Choose the right material
- Standard concrete mix: Suitable slabs, steps, and footings when the product meets the project requirements.
- Fast-setting concrete: Suitable post installations and rapid-setting applications specified on the bag.
- High-strength concrete: Projects requiring its specified strength and performance.
- Sand or topping mix: Suitable thinner repairs and overlays within the product's thickness limits.
- Mortar mix: Laying brick or block with the appropriate mortar type. It is not a substitute for slab concrete.
- Concrete resurfacer: Thin renewal of suitable, sound existing concrete. It does not create a new structural slab.
Shopping checklist
Appropriate mix, mixing tub or wheelbarrow, water, shovel, level, and the protective equipment specified by the product.
Estimate your quantity
Slab cubic feet = length in feet × width in feet × thickness in inches ÷ 12.
Round hole cubic feet = 0.7854 × diameter in feet × diameter in feet × concrete depth in feet. Subtract volume occupied by the post or gravel within that space.
Bags needed = required cubic feet ÷ yield per bag. Round up and allow for waste.
Example: A 4-by-6-foot slab at 4 inches thick requires 8 cubic feet. At a stated yield of 0.60 cubic foot per bag, that is 14 bags before any additional waste allowance.
Confirm the actual bag yield, water ratio, curing instructions, and temperature limits. Structural work needs appropriate design and local requirements.
Explore Building Materials →7. Mailbox Installation: Shopping Checklist
Before you shop
Is this a new installation or replacement? Determine whether you need a roadside or wall-mounted mailbox and identify compatible supports.
Shopping checklist
- Mailbox and compatible post or mounting support
- Mounting bracket and exterior-rated fasteners
- House numbers
- Measuring tape, level, and suitable digging tools
- Gravel or concrete only if specified for the approved support design
Plan the installation
Confirm placement and installation requirements with your local postmaster. Check local restrictions and use an appropriate roadside support.
If the approved design calls for concrete, use the concrete guide above to estimate volume, subtracting post and gravel displacement.
Contact 811 before digging and confirm utility marking is complete before work begins.
Explore Hardware Supplies →8. Fence Posts: Materials & Quantities
Before you shop
Bring your fence length, height, panel or rail requirements, gate locations, and planned post spacing.
Shopping checklist
- Posts rated for the intended ground contact
- Compatible rails or panels and exterior-rated hardware
- Post caps, string line, level, and measuring tape
- Post-hole digger
- Gravel and concrete if specified by the design
Estimate your quantity
For a simple straight run: divide run length by maximum post spacing, round up to whole intervals, then add one post.
Example: A 48-foot straight run with a maximum 8-foot spacing needs six intervals and seven posts. Adjust for corners, gates, and shared posts.
Use the concrete guide to estimate concrete per hole. Hole size, embedment depth, and concrete use depend on the fence design, soil, frost conditions, and local requirements.
Confirm boundaries, permits, and easements. Contact 811 before digging.
Explore Hardware & Farm Supplies →9. Concrete Block Walls: Material Estimates
Before you shop
Know your wall length, height, block dimensions, and wall purpose. Retaining, foundation, and load-bearing walls have specific design requirements.
Shopping checklist
- Specified blocks, including corner and half units
- Compatible masonry mortar
- Footing, reinforcement, and grout materials required by the design
- Trowel, level, string line, jointer, and protective equipment
Estimate your quantity
For nominal 8-by-8-by-16-inch blocks, estimate approximately 1.125 blocks per square foot of wall face.
Example: A 20-by-4-foot wall has 80 square feet of face area and needs about 90 blocks before adjustments for openings, cuts, and waste.
Use your mortar product's coverage information for the actual block and joint dimensions.
This is a quantity estimate, not a structural design. Footing, drainage, reinforcement, and grouting must meet the project requirements.
Explore Building Materials →10. Brick & Block Repair: Mortar & Tools
Before you shop
Identify whether you have a loose unit, damaged joints, or wider movement. Bring photos of the existing masonry and mortar.
Shopping checklist
- Mortar or repair material compatible with the existing masonry
- Pointing trowel, joint tool, and brush
- Suitable removal tools
- Bucket, water, and protective equipment
Estimate your quantity
Joint volume = total joint length × repair width × repair depth, using consistent units.
Example: Thirty linear feet of joints at 3/8 inch wide and 3/4 inch deep is approximately 0.059 cubic foot before waste.
Convert the repair volume to bags using the exact product's yield.
Match mortar to the masonry, especially older or softer brick. Moving cracks, leaning walls, or bulging masonry need professional evaluation. Follow dust-control and protective-equipment instructions.
Explore Masonry Supplies →Painting & Staining
Bring your measurements and project questions to our paint counter for help choosing products, finishes, and supplies.
11. Interior Paint: Gallons & Primer
Before you shop
Measure room length, width, and ceiling height. Note doors, windows, surface condition, desired sheen, and any major color change.
Shopping checklist
- Interior paint and appropriate primer if needed
- Patching compound, caulk, and sandpaper
- Brushes, roller supplies, and trays
- Painter's tape and drop cloths
Estimate your quantity
Wall area = room perimeter × wall height − openings.
Gallons = paintable area × number of coats ÷ stated coverage per gallon.
Example: A 12-by-14-foot room with 8-foot walls has 416 square feet of gross wall area. Subtracting 40 square feet for openings leaves 376. Two coats at 400 square feet per gallon require about 1.88 gallons, rounded up to two.
Calculate primer separately using its label coverage. Product, texture, color change, and application method can affect quantities.
Explore Benjamin Moore Paint & Supplies →12. Painting a Room: Supply Checklist
Before you shop
Decide whether you are painting walls, ceilings, trim, or all three. Check for surface damage and identify the existing finish.
Shopping checklist
- Paint for each surface and suitable primer if required
- Angled brush, roller frame, appropriate roller sleeves, and extension pole
- Tray, liners, stir sticks, and paint opener
- Painter's tape, drop cloths, and masking materials
- Patch compound, putty knife, and sanding sponge
- Caulk, caulk gun, and cleaning supplies
- Suitable ladder, gloves, and rags
Estimate your quantity
Calculate walls, ceiling, and trim separately using the coverage and coat requirements for each product.
Example: A 12-by-14-foot ceiling is 168 square feet. Two coats at 400 square feet per gallon require 0.84 gallon, rounded up to one.
Clean, repair, and prime as needed. Follow ventilation and ladder safety instructions. Older coatings may contain lead; seek appropriate guidance before disturbing them.
Explore Painting Supplies →13. Exterior Painting: Prep & Supplies
Before you shop
Identify your siding material and existing finish. Note peeling paint, bare wood, mildew, access needs, and the expected weather.
Shopping checklist
- Exterior paint compatible with the surface
- Appropriate exterior primer
- Exterior caulk and patching materials
- Scrapers, sanding tools, and cleaning supplies
- Suitable brushes, rollers, or spray equipment
- Drop cloths, masking supplies, safe access equipment, and protective equipment
Estimate your quantity
Gallons = net surface area × required coats ÷ product coverage per gallon.
Example: 1,200 square feet of siding with two coats at 350 square feet per gallon requires about 6.86 gallons, rounded up to seven.
Follow temperature, surface-moisture, preparation, and recoat requirements. Older coatings may require lead-safe preparation. Plan safe access before starting.
Explore Exterior Paint →14. Deck Staining: Coverage & Supplies
Before you shop
Measure the deck, stairs, and railings. Identify wood condition and any previous coating.
Shopping checklist
- Deck stain compatible with your wood and existing finish
- Deck cleaner or stripper if required
- Recommended brush, pad, or roller
- Masking supplies, drop cloths, and protective equipment
- Sanding tools and moisture-checking equipment as needed
Estimate your quantity
Gallons = total stainable area × required coats ÷ stated coverage per gallon.
Example: A 12-by-16-foot deck has 192 square feet of flat surface. At 200 square feet per gallon for one coat, that is about one gallon before adding stairs, rails, posts, and waste.
Transparent and solid stains can have very different coverage rates. Follow preparation, wood-moisture, drying, and application instructions. Do not assume every stain needs two coats.
Ask our team about deck sander rentals.
Explore Exterior Stain →15. Fence Staining: Coverage & Supplies
Before you shop
Measure fence length and height, and decide whether you will coat both sides. Note picket spacing, wood condition, and any previous finish.
Shopping checklist
- Compatible exterior wood stain
- Wood cleaner and preparation tools
- Brush, pad, or sprayer recommended for the stain
- Masking materials, drop cloths, and protective equipment
Estimate your quantity
Basic face area = fence length × height × number of sides being coated.
Then add rails, posts, edges, and other coated surfaces. Divide the total area multiplied by required coats by the product's coverage per gallon.
Example: A 60-foot fence at 6 feet high, coated on both sides, has 720 square feet of basic face area. One coat at 250 square feet per gallon needs about three gallons before adjustments.
Rough wood, picket spacing, and spray overspray affect quantities. Protect nearby property and plants, and follow weather and wood-moisture requirements.
Explore Fence Stain Options →Bring Your Measurements. Bring Your Questions.
Our team can help you work through quantities, compare products, and build your shopping list. Visit Country Paint & Hardware at 2410 Foxon Road in North Branford.